Cyclone 4006 Runway Paint & Rubber Removal

The Cyclone 4006 vehicles wash with ultra high pressure and are specifically designed for cleaning airport runways of rubber and paint.

Description

Cyclone 4006AC (Airport Chassis)

This ultra-high pressure cleaning vehicle is designed specifically for removing rubber and paint from airport runways. Its specially shaped turbine blades create a vortex (cyclone!) of air, water, and loosened rubber or paint at 140 mph. A high-volume macerator pump further emulsifies the recovered waste water into a large 1,000 gallon waste recovery tank near the rear of the vehicle. It’s also able to dump solid waste material separately from waste water with the press of a button.

Features

  • Spacious operator’s cab offers direct visibility to the cleaning head
  • Water capacity allows for up to 5 hours of continuous operation
  • Able to return the friction coefficient to acceptable levels in a single pass
  • Fresh water filters remove organic material and particles to 0.35 microns
  • Able to clean markings to restore reflectivity without removing glass beads
  • Compare Before and After

    Technical Specifications

    Cleaning Head Assembly Permanently mounted, hydraulically controlled, multi-pivot point maneuverability. Cast aluminum housing, hydraulically driven rotation,
    fiberglass recovery tank. Belt-driven return pump. Stainless steel ultra high pressure components. Instantaneous recovery
    Cleaning Attachment Gas powered, remote paint removal head up to 300ft. (91m) distance
    Rubber Removal Head 40in. (1.01m) cast aluminum head with up to 34in. (0.86m) cleaning path
    Paint Removal Head 24in. (60.96cm) cast iron with adjustable 6in. (15.24cm) to 16in. (40.64cm) cleaning path
    Productivity (Rubber) Up to 20,000ft2. (1,858m2) per hour
    Productivity (Paint) Up to 3,000 linear ft. (914m) per hour
    Filtration System Inlet water filtered to 0.35 micron over 260 ft.2 of organic and particulate filtration
    Water Filters Minimum of two (2) filters before UHP pump: One (1) organic 50 micron filter, one (1) particle 0.35-micron filter
    Water Pump Positive displacement triplex plunger, with full pressurized lubrication, water cooled, 5.7gal. (21.6L) per minute @ 40,000psi, 22.6 L/
    min. @ 2,758 bar, variable output from 6,000 psi (413 bar) to 40,000 psi (2,758 bar)
    Fresh Water Tank 1,600gal. (6,000L) corrosion resistant fiberglass
    Reclaim Tank Sand blasted and powder coated stainless steel. (Available in carbon or stainless steel). Separates water from material. 2,100gal.
    (7,949L) total capacity. Powered dump with powered door for easy maintenance
    Chassis 10in. (0.25m) x 3in. (0.08m) x ¼in. (0.0064m) wall cold rolled steel tubing frame on a 23,000lb. (10,433kg) rear axle and a 20,000lb.
    (9,072kg) front axle
    Operating System Foot pedal controlled hydrostatic drive
    Controls Automated cleaning controls. Computer monitored safety and maintenance system with automatic shutdown
    Speeds Variable operating speeds and transport speed up to 18mph (28.9km/h)
    Brakes Air brakes, front and rear automatically adjusted 4 wheel drum brakes
    Dimensions L = 30ft. (9.14m) x W = 8ft. (2.44m) x H = 10ft. (3.05m)
    Fuel Tank 100gal. (379L) total fuel capacity
    Gross Vehicle Weight Rating 56,000 lbs. (25,454 kg)
    Steering Hydraulic power steering
    Power Plant Engine 9.0L Power Tech Interim Tier 4 / Stage III B, 375hp turbocharged liquid cooled diesel engine
    Pump Safety Pressure relief burst disk will relieve all pressure if there is an increase of 7% above maximum recommended operating pressure

    Cyclone 4006HT (Heavy Truck)

    Features

  • Up to 25,000ft² (2,300 m²) of effective rubber removal per hour using less than 6 gpm (23 L/min)
  • Self-contained cleaning system integrated with a Class 8 truck chassis
  • Ability to service multiple airports in a region
  • Roadway paint-line removal
  • Up to 5 hours of continuous operation using just 1600 gallons (6,000 L) of water
  • Simple design results in ease of use, serviceability, and maintenance
  • Technical Specifications

    Cleaning Head Assembly Removable, joystick controlled, multi-pivot point maneuverability. Cast aluminum housings, hydraulically driven rotation, fiberglass recovery tank. Belt-driven return pump. Each head max work pressure is 40,000 psi (2,700 bar) at 6 gpm (21L/min) Each head has a separate return tank and filtration screen.
    Cleaning Attachment Gas powered, remote paint removal head operates up to 300ft. (91m) distance from the main unit.
    Rubber Removal Head 40in. (1.01m) cast aluminum head with up to 34in. (0.86m) cleaning path
    Paint Removal Head 24in. (60.96cm) cast iron with adjustable 6in. (15.24cm) to 16in. (40.64cm) cleaning path
    Productivity (Rubber) Up to 20,000ft2. (1,858m2) per hour
    Productivity (Paint) Up to 3,000 linear feet (914m) per hour
    Filtration System Inlet water filtered to 0.35 micron over 260ft2 (24m2) of organic and particulate filtration
    Water Filters Minimum of two (2) filters before UHP pump: One (1) organic 50 micron filter, one (1) particle 0.35-micron filter
    Water Pump Positive displacement triplex plunger, with full pressurized lubrication, water cooled, 5.7gal. (21.6L) per minute @ 40,000 psi (2,758 bar), variable output from 6,000 psi (413 bar) to 40,000 psi (2,758 bar)
    Fresh Water Tank Fresh water capacity: 1,600gal. (6,000L) standard. Available up to 2,200 gal (8,327L) for 6.5 hours of operating time
    Reclaim Tank Separates water from material. 2,000gal. (7,570L) total capacity. Sand blasted and powder coated stainless steel. Carbon steel tank is painted with polyurethane paint. Powered dump with powered door for easy maintenance
    Chassis Third party chassis available (MACK is shown in picture). 6X4 style, GVWR 57,320lbs. (26,000kg)
    Operating System Creep drive. Independent cooling/radiator, package. Travel in drive or hydrostatic mode. Cleaning mode: Engine operates at 1,550RPM
    Controls Automated cleaning controls. Computer monitored safety and maintenance system with automatic shutdown
    Speeds Cleaning speed: Up to 3.7mph (6km/hr), transport speed: Up to 65mph (105km/hr)
    Brakes Air brakes, front and rear automatically adjusted 6 wheel drum brakes
    Dimensions (Dimensions with cleaning heads retracted): 34ft. 4in. L x 8ft. W x 11ft. 6in. H (10.5m x 2.4m x 3.5m)
    Fuel Tank Up to 105 gal (400L) total fuel capacity
    Gross Vehicle Weight Rating Up to 72,600 lbs. (33,000 kg)
    Steering Power Steering
    Power Plant Engine Turbocharged liquid cooled diesel engine or equivalent
    Pump Safety Pressure relief burst disk will relieve all pressure if there is an increase of 7% above maximum recommended operating pressure

    Cyclone 4006 ST

    Features

  • Small truck chassis for easy transport between cleaning sites or offsite waste disposal.
  • Cleaning heads easily changeable from rubber removal to paint removal.
  • 34in (0.86 m) wide cleaning path for rubber removal, adjustable cleaning path for paint removal from 6in (0.15 m) to 16in (0.41m).
  • Fresh water tank provides up to 2 hours of operating time.
  • LCD operator interface provides fully computerized control and automated operation for the most efficient runway cleaning operations.
  • Technical Specifications

    Cleaning Head Assembly Permanently mounted, joystick controlled, multi-pivot point maneuverability. Cast aluminum housing, hydraulically driven rotation, fiberglass recovery tank. Belt-driven return pump. Rubber or Paint removal head max work pressure is 43,500psi (2,700bar) at 6gpm (21L/min). Can easily be changed from Paint to Rubber removal in minutes.
    Cleaning Attachment Gas powered, remote paint removal head operates up to 300ft (91m) distance from the main vehicle.
    Rubber Removal Head (1)40in (1.01m) cast aluminum head, with up to 34in (0.86m) cleaning path. Hydraulically actuated with a multi-axis arm, joystick-controlled by the operator.
    Paint Removal Head (1) 24in (60.96cm) cast iron head with adjustable 6in (15cm) to 16in (41cm) cleaning path. Hydraulically controlled with a multi-axis arm for easy maneuverability will produce from 6in (15cm) to 16in (41cm) path of paint removal
    Productivity (Rubber) Up to 25,000ft² (2,322m²) per hour for rubber removal*
    Productivity (Paint) Up to 10,000 linear feet (3048 meters) per hour**
    Filtration System Inlet water filtered to 0.35 micron over 260 ft² of organic and particulate filtration
    Water Filters Minimum of two (2) filters before UHP pump inlet: One (1) organic 50 micron filter, one (1) particle 0.35-micron filter. Combined filter media surface area of over 260ft²
    Water Pump Positive displacement, triplex plunger, with full pressurized lubrication, water cooled, 5.7gal (21L) per minute up to 40,600psi (2,800bar). Variable output from 10,000psi (689bar) to 40,600psi (2,800bar)
    Fresh Water Tank Capacity: 530gal (2,081L) internally baffled, constructed of corrosion resistant fiberglass.
    Reclaim Tank Separates water from material. 600gal (2,271L) total capacity. Powered dump with powered door for easy maintenance. Available in carbon or stainless steel.
    Chassis Third party chassis available (Ford F-550 is shown in the picture). 4X2 style
    Operating System Hydraulic creep drive. Independent cooling/radiator, package. Travel in drive or hydrostatic mode.
    Controls Automated cleaning controls. Computer monitored safety and maintenance system with automatic shutdown
    Speeds Cleaning speed: Up to 3.7mph (6km/h), transport speed: Up to 65mph (105km/h)
    Brakes Hydraulically actuated 4 wheel disc brakes
    Dimensions 28ft 6in L x 7ft 10in W x 6ft 9in H (8.69m L x 2.39m W x 2.06m H) (Fits into a standard shipping container)
    Fuel Tank 40 gal (151L) total fuel capacity
    Gross Vehicle Weight Rating 19,500 lbs (8,845 kg)
    Steering Power steering
    Power Plant Engine Engine is a 400 HP (298 kw) 6.7L Powerstroke V8 with an intercooled turbocharger, diesel direct injection, air filter with pre- separator, radiator cooler with fan and sensor to measure the coolant temperature
    Pump Safety Pressure relief burst disk will relieve all pressure if there is an increase of 7% above maximum recommended operating pressure

    Cyclone 4006 LT

    Features

  • Standard Cyclone system for rubber and paint removal incorporated onto a smaller truck.
  • Truck chassis allows for transport speeds up to 65 mph/h.
  • 800 gallon of fresh water for up to 3 hours of continuous operation.
  • Lowest water consumption in the industry, less than 6.07 gallon/min.
  • Technical Specifications

    Cleaning Head Assembly Permanently mounted, hydraulically controlled, multi-pivot point maneuverability. Cast aluminum housings, hydraulically driven rotation, fiberglass recovery tank. Belt-driven return pump. Each head max work pressure is 40,000 psi (2,700 bar) at 6gpm (21L/min) Each head has a separate return tank and filtration screen. The spin of the Cyclone head creates vacuum like recovery*.
    Rubber Removal Head 40in (1.01m) cast aluminum head with up to 34in (0.86m) cleaning path
    Paint Removal Head 24in (60.96cm) cast iron with adjustable 6in (15.24cm) to 16in (40.64cm) cleaning path
    Productivity (Rubber) Up to 20,000ft2 (1,858m2) per hour
    Productivity (Paint) Up to 10,000 linear feet (3048 meters) per hour
    Filtration System Inlet water filtered to 0.35 micron over 260ft2. of organic and particulate filtration
    Water Filters Minimum of two (2) filters before UHP pump: One (1) organic 50 micron filter, one (1) particle 0.35-micron filter
    Water Pump Positive displacement triplex plunger, with full pressurized lubrication, water cooled, 5.7gal per minute @ 40,000 psi, 22.6 L/min. @ 2,758 bar, variable output from 6,000 psi (413 bar) to 40,000 psi (2,758 bar)
    Fresh Water Tank Fresh water capacity: 800gal (3,028L), reclaim capacity: 1,000gal (3,785L)
    Reclaim Tank Separates water from material. 1,000gal (3,785L) total capacity. Powered dump with powered door for easy maintenance (Available in carbon or stainless steel)
    Chassis Third Party chassis available
    Operating System Split shaft PTO with creep drive. Independent cooling/radiator, package and hot shift PTO to engage/disengage water pump, travel in drive or hydrostatic mode. Cleaning mode: Engine operates at 1,500RPM
    Controls Automated cleaning controls. Computer monitored safety and maintenance system with automatic shutdown
    Speeds Cleaning speed: Up to 6km/hr transport speed: Up to 105km/hr
    Brakes Air brakes, front and rear, automatically adjusted 4 wheel drum brakes
    Dimensions (Dimensions with cleaning heads retracted): L 34ft 4in x 8ft x 11ft 6in (10.5m x 2.4m x 3.5m)
    Gross Vehicle Weight Rating 33,000 lbs (15,000 kg)
    Pump Safety Pressure relief burst disk will relieve all pressure if there is an increase of 7% above maximum recommended operating pressure